![]() |
![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
#1
|
|||
|
|||
Is My Pump to Strong?
Hey everybody i just set up an Aquapod 24....a lot of people recommended swapping the stock pump for the Maxi-Jet 1200 so i did...it looks too powerful...there are little air bubbles being blown all over the place at every level of the tank...is this natural in a new tank? Will they eventually go way or is this a problem?
thanks in advanced |
#2
|
|||
|
|||
Are the bubbles coming from the pump? If so are you sure you have enough water in the back chambers?
|
#3
|
|||
|
|||
never mind i fixed it...there was a tube bringing air from the surface causing the bubbles im guessing
however i do have on more question...is there anyway to be sure that water is actually being filtered through the sponge and filter floss? unlike the stock pump, on the maxi-jet there isnt a whole sucking in water....also the MJ is in the display...should i just not worry about it? i just dont see how water is being circulated through the back chambers and not just filling them up |
#4
|
|||
|
|||
You don't have a return pump located in the rear chambers?
__________________
Mathias Hofstadter's Law - It always takes longer than you expect, even when you take into account Hofstadter's Law. |
#5
|
|||
|
|||
all i have is the maxi-jet in the display tank...
|
#6
|
|||
|
|||
I haven't had an aquapod, but I believe they're basically the same thing as all the other cubes out there. A false wall on the back, with an overflow, and a return jet. On all the models I've seen, you're supposed to have a pump in one of the back chambers, hooked up to a tube that goes to the return jet. This causes water to spill over the overflow, and you should keep the water level in the rear chambers lower than the level in the main display so the surface scum spills over into the filtration area.
__________________
Mathias Hofstadter's Law - It always takes longer than you expect, even when you take into account Hofstadter's Law. |
#7
|
|||
|
|||
so the mj should go in the rear chamber? and what is the return jet?
|
#8
|
|||
|
|||
Hey, no offense, but I think you need to bone up with a little reading.
Like I said, I haven't had an aquapod, but I believe it's no different than the other cubes out there. All the cubes I have seen have a pump in one of the rear chambers, opposite of the side of the tank with the grated overflow. Then, there should be some sort of nozzle, or hole, or jet in the wall for the water to return to the display from the rear filtration area.
__________________
Mathias Hofstadter's Law - It always takes longer than you expect, even when you take into account Hofstadter's Law. |
#9
|
|||
|
|||
no offense taken, let me try and explain what is going on...i swapped out the stock pump for a maxi-jet 1200 because from what ive read the stock pump has noise and heat issues...however, on the stuck pump there are two nozzles, one expels water and the other draws it in....on the mj there is no second nozzle only one to expel the water...i dont under stand how the water is actually being circulated through the back chambers
|
#10
|
|||
|
|||
all pumps have a intake and exhoust. post a pic of how you have it setup and we can help a little better.
__________________
I belong to reefahaulics annonymus. "My name is Steve and im an addict." |
#11
|
|||
|
|||
The stock pump is located in the back. When you removed it, you should have put the MJ in the same place that the stock pump was taken from, not in a totally different place i.e. the display. if the inputs/outputs are different sizes, then you may need to get adapters to fit. In my cube, the pump in the back only connects to an output; the input just draws water from the chamber it's in.
|
#12
|
|||
|
|||
there is no way to fit the MJ in to the whole in the wall and the tube from the stock pump doesnt fit around the MJ...pics are coming in a minute
|
#13
|
|||
|
|||
then you need to get a tube and maybe some size adapters to make it fit!
__________________
baby it was on sale half price I PROMISE!!!! |
#14
|
|||
|
|||
this was my original set up
![]() but i dont see how it will fit in the back chamber ![]() i tried to use the tube from the stock pump but it is to big to fit around the MJ |
#15
|
|||
|
|||
Oh My Go.... whatever. I am seriously frustrated now. Take your tank back to the store, along with the MJ.
Unless this is a joke. In which case, it isn't funny at all |
#16
|
|||
|
|||
Uh.... I have to agree with mikellini - we're willing to help, but, are you joking around here? You'd be correct to assume that no water is being drawn through the filtration chambers with your current arrangement...
__________________
Mathias Hofstadter's Law - It always takes longer than you expect, even when you take into account Hofstadter's Law. |
#17
|
|||
|
|||
someone please point out the obvious for me...
the second pic isnt how i tried to run it i was just trying to show the pump in relationship to the hole in the back wall |
#18
|
|||
|
|||
take the slotted guard off the the intake for the MJ, turn it sideways and on its back (with the output facing up) and lower it down into the chamber. Before doing this you might want to attach the output hose that was on your stock pump to the output on the MJ. And if it's too big (which it probably is), you need to either get an adapter or use a zip tie on the hose to tighten it down.
Sorry but I can't understand how you don't see how it would fit. How did the stock pump fit? It didn't attach directly to the output, it attached to a tube and sat at the bottom of the chamber. Reason would lead you to the conclusion that if you were to replace the stock pump, the replacement would go in the same place (roughly) |
#19
|
|||
|
|||
wow... dude you dont need all that stock crap on the MJ. Take it all off and attach the tube and just ....slide it in!!
|
#20
|
|||
|
|||
The maxijet needs to REPLACE the stock pump. Do you remember how the stock pump was in there?
Well, this pump will sit the exact same way. Skinny nozzle will go into tube and voila. Here's a diagram. ![]() |
#21
|
|||
|
|||
aright thanks for the help....i dont know why i didnt think of that
|
#22
|
|||
|
|||
Merry Christmas and God bless you all.. you are far more patient than I am.
__________________
26 gallon bowfront sps: 10 gal sump/fuge w/ MAG 5 return on SQWD, SEIO 820, 2 MJ900s and MJ600 on wavetimer, CPR HOB skimmer, Aquamedic 250W 15K MH, URI 18" VHO x2 |
|
|