|
#1
|
|||
|
|||
FS: EuroReef CS6-2 400W Electronic MH Ballast
Hey i have a used Euroreef Skimmer, model CS6-2, great condition, used with Pump. $100 or 115 Shipped to the lower 48.
Second i have a 6 month old Coralvue Metal Halide Electronic Ballast. its a 400w single bulb unit, and i will include the 20K Coralvue bulb as well, its also 6 months old. They were used for about 6 hours a day, so still have lots of use left in em. Looking for $100 or $110 shipped. I live outside of Portland Oregon. Also have a 90g Acrylic Hex tank in portland im lookin to sell, great condition with stand. Tim
__________________
I feel sorry for people who don't drink. When they wake up in the morning, that's the best they're going to feel all day. -Frank Sinatra |
#2
|
|||
|
|||
pm sent
|
#3
|
|||
|
|||
Interested in the ER...............PM sent.
|
#4
|
|||
|
|||
PM sent around 8am this morning with questions, I am very interested.
|
#5
|
|||
|
|||
I would like to purchase the euroreef skimmer if still avaiable.
|
#6
|
|||
|
|||
I will take coral vue ballast and light setup shipped
|
#7
|
|||
|
|||
pm sent again on skimmer.
|
#8
|
|||
|
|||
ya sorry everyone, i had a billion PM's, and a tough day at work. I think everything is sold. Sorry again for the lack of info, just wasnt quite one of those days at work when i could step away and check my email. Thanks again everyone.
Tim
__________________
I feel sorry for people who don't drink. When they wake up in the morning, that's the best they're going to feel all day. -Frank Sinatra |
#9
|
|||
|
|||
If the 400w is not sold LMK.
|
#10
|
|||
|
|||
I have attempted to contact you again Tim.
__________________
With a Router and a Table saw you can make anything for your tank. |
#11
|
|||
|
|||
Your PM box is full again, and either you are not getting your emails or intentionally ignoring me.
SUMMERS wrote on 10/03/2007 04:53 PM: Items arrived today........there are a couple of issues. http://img254.imageshack.us/img254/1233/1002147mft1.jpg http://img254.imageshack.us/img254/1010/1002148mmp7.jpg The skimmer has a chip out of the base, noticable as soon as the package was opened. The neck of the skimmer is not connected to the body at all. http://img254.imageshack.us/img254/610/1002149mxm3.jpg The cord on the pump is melted. http://img512.imageshack.us/img512/6524/1002152mte7.jpg http://img512.imageshack.us/img512/251/1002151mqe2.jpg The ballast does not have the power cord with it.......I used one from a computer monitor and it does not fire the bulb at all. No hum from the ballast which leads me to believe it is not getting any power or does not work. Now I work with acrylic so I can fix the neck of the skimmer and the broken piece on the bottom. But I can not fix a melted cord or a ballast that does not work. What resolution do you suggest at this point? Larry ------------------ SUMMERS wrote on 10/03/2007 09:42 PM: I can fix the skimmer.......no problem there altough I did not expect to do a patch job........the pump does work on it and I figure after a day or two in a vinegar bath it will clean up fine and will be able to be re-glued........the cord on the pump is melted though, as can be seen in the pictures.......I will see if I can replace it as I will not feel confortable when not at home with it running like that.....the wires are not bare but the plug is surely melted. I have tried two other bulbs on the ballast and still nothing......do I need the cord that came with the ballast?...never had a problem with any other ballast using a different cord..........I will check a few other things and get back to you shortly.. Best Regards, Larry -------------- SUMMERS wrote on 10/03/2007 11:25 PM: Tim, the ballast is no good. I have tested it with a volt meter and nothing registers. The bulb works, as I have ired it on another ballast. I will return the ballast via USPS priority in the morning. The skimmer I will keep as I can fix the broken pieces with weld-on. Let me know an address to return the ballast to. Payment can be refunded through Paypal on it. You can reach me at ###### or provide a number for me to contact you. Best Regards Larry ------------- I know you got the email last night. You really need to refund all of my money.
__________________
With a Router and a Table saw you can make anything for your tank. |
|
|