|
|
|
Thread Tools | Search this Thread | Display Modes |
#201
|
|||
|
|||
ray22... no problem. Glad that you found this thread useful and happy that it saved you a nice chunk of change.
The questions about the bulkheads are pretty easy. The double threaded ones have an internal thread on the internal of the outside the tank piece. You will have to use Teflon tape and a piece of PVC called Male Pipe Thread to Slip . This will allow you to change the plumbing later. The second type of BulkHead is the more standard Slip fitting. This needs to be solvent glued to a slip fit piece of PVC at the connection making this connection permanant. Hope this helps some. |
#202
|
|||
|
|||
Great thread, Just One More Tank.
Very informative. I ordered 2 drill bits from the ebay listing you mention. Lau said they are on their way. I am setting up my new 180 r/r tank. Will be drilling my sump and refugium following the step by step procedure you so neatly have shown us all. Thanks. |
#203
|
|||
|
|||
Quote:
Good luck with the drilling. Take it slow and gently and you should not have any problems. |
#204
|
|||
|
|||
What would you suggest for drilling a 2.5g tank? I used to manage a fish store and the big huge drill we had was ok for 10g and up, but it would be to big for such a small tank. Is there anything store bought I can use to drill it?
|
#205
|
|||
|
|||
I completed drilling my sump and refugium tanks with the drill bits I ordered from Lau in Hong Kong. By simply following the instructions from Just One More Tank, it was no problem at all.
This was the first time I have ever tried drilling glass. By reading this thread I was able to figure out just what size bits I would be using, and there is also a conversion link on Reff Central home page. I would like to thank the starter of this thread( Just One More Tank) for taking the time to post such graphic detailed instructions. Thanks and read on. |
#206
|
|||
|
|||
Quote:
I was very nervous the first few times that I drilled a few bulkhead holes in a handful of glass tanks. Now it is no sweat. I just wanted to help take some of the fear and uncertainty out of the process for those who need/want to have this done. I wanted a fairly organized step by step approach that beginners could follow and have excellent results. I am glad that this could help so many people out. Reef Central is a great resource! |
#207
|
|||
|
|||
I got my bits today. One question for those who have done this. I am drilling a 80mm hole through 3/8" glass, do you think one bit will be enough?
__________________
Steve 280 Gallon BB mixed reef PM bullet 3 powered by a PCX-70,400w HQI Radiums,Tunze Wavebox,AC III Litermeter III,PCX-70 pushing 2 Eductors,Geo 624 Ca Reactor,125 sump, Dart Return |
#208
|
|||
|
|||
|
#209
|
|||
|
|||
Quote:
__________________
It can always be worse.. |
#210
|
|||
|
|||
Quote:
|
#211
|
|||
|
|||
How many 1.75" holes do you think I should be able to drill in the back of a standard all-glass 75g tank? I am hoping to get 5 holes on the back but will not do this if it will cause the strength of the tank to decline to a dangerous level.
Thanks for any input. Bob |
#212
|
|||
|
|||
Is Shank size an issue?
I'm looking at ordering a 45 mm bit through Lau on ebay. It says the shank on the bit is 10 mm which comes out to 0.39 inches. That's just over 3/8", the size of the chuck on my drill. Is this an issue or is there enough room to fit the 10 mm shank into my 3/8" drill?
__________________
What I hear, I forget. What I see, I remember. And what I do, I understand. -Chinese Proverb |
#213
|
|||
|
|||
3/8 = .375
.39 -.375 = .015 That's just 15 thousandths of an inch. It shouldn't be a problem.
__________________
daFrimpster illegitimus non carborundum |
#214
|
|||
|
|||
Well thanks for starting this thread. Got my bits from Lau++
and bulkheads. I'm ready to drill. ALL NEED IS THE TIME GET IT DONE. |
#215
|
|||
|
|||
Well thanks for starting this thread. Got my bits from Lau++
and bulkheads. I'm ready to drill. ALL NEED IS THE TIME GET IT DONE. |
#216
|
|||
|
|||
Now how that double post ? Sorry
|
#217
|
|||
|
|||
Hey! Thanks for the triple post ... errr... I mean bump.
|
#218
|
|||
|
|||
Well, after drilling 12 holes (8mm) of the 60 I will be cutting to make slots for an external overflow, I can say the following:
- using a drill press makes it much easier - 1100 RPM's cuts much better than 620 RPM's - definately use a piece of tape on the back side (duct or something similarly sticky and wide) - drilling the holes is really quick. The long part is prepping each hole (I'm getting rather tired) Bob |
#219
|
|||
|
|||
Quote:
|
#220
|
|||
|
|||
Quote:
__________________
It can always be worse.. |
#221
|
|||
|
|||
I'm about to drill my 75g as well. Just ordered the hole saw from lau but wanted to run this by everyone before starting. This thread has been a great help, the lfs wanted $40 per hole. This will save some money for other fishy things. Take a look at my plan and advise. Do you think that there are too many holes? Should I just run the CL return over the top?
Thanks everyone. |
#222
|
|||
|
|||
Also the CL drain will be joined and run into a Mag12 then returned and split to the two 3/4 returns. Each 3/4 return will then be split using a loc-line. The plumbing will probably be 1" pvc all around.
As for the sump/refugium I'll be using a Mag7 for the return with 1 1/4" pvc. What do you all think? Vance |
#223
|
|||
|
|||
Does any one have a suggestion for placement regarding drilling the holes that drain and return to/from the sump? I was considering installing an internal overflow but would rather not since they take up so much space. The internal overflow would probably be 10" long by 5" deep.
|
#224
|
|||
|
|||
to the top ^
|
#225
|
|||
|
|||
For those of you drilling for overflows, what are you using for the actual overflow
__________________
Steve 280 Gallon BB mixed reef PM bullet 3 powered by a PCX-70,400w HQI Radiums,Tunze Wavebox,AC III Litermeter III,PCX-70 pushing 2 Eductors,Geo 624 Ca Reactor,125 sump, Dart Return |
|
|